How do I fix E20 error on my Electrolux washing machine?
The problem may be solved by switching off the power to the washing machine for about 1-2 hours and then starting a wash cycle again. If the pump has been blocked, a bimetal fuse will switch off the pump. When the pump has cooled down, it should work normally.
What does E20 mean on Hotpoint washing machine?
On some models an obstruction or blockage in the drain pump may cause E20 to appear in the display. Please watch our video clip to show you how to check for and remove any blockages from the drain pump.
How do you manually drain a washing machine?
If not, follow these steps:
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose at the back of the washing machine.
- Step 3: Drain the water.
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose.
- Step 3: Drain the water.
- Step 4: Scrub the filter.
How do I force my Electrolux washer to drain?
Drain Pump Guard Filter
- Open the pump guard panel.
- Pull the emergency hose out.
- Place the hose in a container and remove its cap.
- Unscrew the pump guard filter.
- Wash the filter in the sink to clean it.
- With the filter out, check the pump impeller.
- Put the pump guard filter and emergency hose back into the machine.
How do you manually drain an Electrolux washing machine?
How to Drain a Top-Loading Washing Machine
- STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one.
- STEP 2: Locate the drain hose and water supply hoses.
- STEP 3: Drain the washing machine of water.
- STEP 4: Remove a drain hose clog.
- STEP 5: Remove a drain pump clog.
How do I know if my washing machine drain hose is clogged?
The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.
How do I know if my washing machine drain pump is bad?
Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying. For front-loading washers, do not attempt to open the door mid-cycle.
What E20 means?
From Wikipedia, the free encyclopedia. E20 or E-20 may refer to: E20 fuel, a mixture of 20\% ethanol and 80\% gasoline.
Where is the drain pump on a washing machine?
The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be. If your washing machine is failing to drain during a wash cycle, it could be that there is a problem with the drain pump.
Why is my washing machine not draining?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I fix E20 error on my Whirlpool washing machine?
Clean the drain pump/filter and then run a hot wash without any soap powder. The problem may be solved by switching off the power to the washing machine for about 1-2 hours and then starting a wash cycle again. Click to see full answer. In this manner, how do I fix e20 error on my washing machine? Ensure correct position of the drain hose.
Why does my washing machine display error messages E20 E21 and C2?
Washing machine displays error message E20, E21 or C2, emits 2 beeps or 2 flashes. 1. Ensure the drain hose is in the correct position The drain hose should extend no more than 10 cm down into the drain.
How do you fix a washing machine that won’t wash?
Switch off the power to the washing machine. The problem may be solved by switching off the power to the washing machine for about 1-2 hours and then starting a wash cycle again. If the pump has been blocked, a bimetal fuse will switch off the pump. When the pump has cooled down, it should work normally.
What are the error messages of the washing machine?
Issue 1 Washing machine displays error message E20, E21 or C2, emits 2 beeps or 2 flashes. 2 Washing machine does not drain 3 The drum does not turn 4 The appliance makes an unusual noise because of the blockage of the drain pump