How do you remove the error code on a Fisher and Paykel dishwasher?

How do you remove the error code on a Fisher and Paykel dishwasher?

To attempt to Clear the Fault Code

1. Press to stop the beeping. Press. again to turn the dishwasher off.
2. Wait a few seconds. Press. again to turn the dishwasher back on.

What does A3 mean on a Fisher and Paykel dishwasher?

A3: Drawer cannot drain. The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault.

Why is my Fisher and Paykel dishwasher not draining?

Straighten any kinks along the hose that drains water from your DishDrawer™. If the kinks return, you may need to replace the hose. Clean the filter plate/drain filter. Aim to clean your DishDrawer™ at least once per month, including the drain filter plates.

What does fc1 mean on Fisher and Paykel dishwasher?

The F1 fault code indicates that water has filled the flood pan beneath the bottom drawer of the machine. Water in the drain pan can also be caused by a drain blockage, a clogged filter, a faulty lid seal or a leaking water-inlet valve.

How do I fix e30 error on dishwasher?

Clean the pump and fluff filter. Then start a hot wash without adding any soap powder to clean out the drainage system. Check for a blocked drain. Check the hose connected to the sink trap, and check if the sink is draining normally to rule out blockage.

How do I fix E5 error on Fisher and Paykel dishwasher?

How To Fix: Check that drain hose is straight. Be sure the drain hose is connected per the installation instructions. Fisher and Paykel Dishwasher Dishdrawer Error Code E5 = The first 3 program indicator lights are flashing. Error Code Cause: Water supply hose is crimped or bent.

What does F9 mean on a Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code F9 Error Code Cause: Electrical Malfunction. How To Fix: Turn power to DishDrawer off then turn on power supply. This may reset error.

What does A20 mean on Fisher and Paykel dishwasher?

Excessive water remaining above the filter plate, after the rinse cycle (This can be displayed as an A20 fault). View for more troubleshooting of your dishwasher.

How do you fix a dishwasher that will not drain?

So before you call a pro, troubleshoot your dishwasher using the following steps.

1. Run your garbage disposal.
2. Clean your sink’s air gap.
3. Remove standing water.
4. Clear up detergent mishaps.
5. De-gunk the drain basket.
6. Check the drain hose for kinks.
7. Examine the drain hose for clogs.
8. Replace the drain hose.

How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

Why is my Fisher and Paykel Dishdrawer beeping?

First and foremost, check the hose of your dishwasher. If it is bent or broken, it may not be draining the water which results in activating the beeps. To fix it, if there is bent, you may be able to replace it yourself and if it is broken, you need to replace it with new one.

How do I fix the F30 code on my dishwasher?

“An F30 code error means the flood switch has been activated. You will need to take the dishwasher out from under the cabinet. Tilt it backwards at a 45 degree angle. There is likely some water under the dishwasher.

What does error F30 mean on a Fisher and Paykel refrigerator?

F30 What this error code signifies is that the display of the refrigerator has a fault. It is important to contact Fisher & Paykel service center and request service or call a qualified refrigerator technician to fix the faults. This is especially needed if you don’t know your way around the refrigerator.

What do I do if my Fisher & Paykel refrigerator displays error codes?

There is an error with the electronic communication if you see either of these error codes displayed. To fix all of these errors and faults, contact Fisher & Paykel for service or call a qualified refrigerator technician. Check out these other related articles…

What do I do if my Fisher and Paykel dishwasher is not working?

Press to turn the dishwasher off and wait a few minutes. Press again to turn the dishwasher back on. If the dishwasher still does not function and/or the problem persists, disconnect the dishwasher from the power supply, turn the water supply off, then contact Fisher & Paykel Customer Care with the fault code information.

What does F2 mean on Fisher Paykel dishwasher?

If your dishwasher has the F error codes, F2 is an error code for a motor problem. A dishwasher that turns on but doesn’t make noise is a good indicator that’s the problem. F1 is the flood switch notice for dish drawer dishwashers by Fisher Paykel.